12V LED driver circuit

Posted by: admin  • Information section:LED

12V LED driver circuit



The buck/boost converter must be used when the input voltage can be higher or lower than the total voltage drop of the LED or LED string. A circuit based on the LT°C3783 buck/boost converter drives eight 1.5A series LEDs as shown in Figure 4. The input voltage range of the LED string driving circuit is 9~36V, and the total voltage drop range of the LED string is 18~37V. Under the condition of VIN=14.4V, Vo=36V and I0=1.5A, the output power is 54W, and the efficiency is up to 93%. The switching frequency of the circuit is determined by the IC pin FREQ

Resistor R5 is set (frequency range is 20kHz~1MHz). The voltage divider composed of R7 and R8 sets the output overvoltage protection level. R4 is connected between IC pin FBP and high side line to sense LED current. The LTC3783 supports multiple topologies. It can also be used to construct circuits such as boost converters and buck converters.

Flyback converters, single-ended primary inductor converters (SEPIC), and CUK regulators can all increase or decrease the input voltage.

The output and input voltage can be the same or opposite in polarity. Each topology has unique advantages, but is less efficient than a buck-boost regulator.
 

 



Tagged:

read ()  •  Sep 20, 2019  •  Edit


YOU MAY ALSO LIKE:

12v led circuit diagram-HV9910 circuit

Date: Sep 21, 2019  | Click 3 times

image

12v led circuit diagram
The LED driver module uses the HV991

benefits of led lighting

Date: Sep 21, 2019  | Click 6 times

image

benefits of led lighting
In the past two years, LED-related

LED driver application and driving method

Date: Sep 20, 2019  | Click 1 times

image

At present, LED is developing rapidly, technology is becomin

What is a wireless LED control card

Date: Sep 20, 2019  | Click 10 times

image

What is a wireless LED control card
The wireless LED control

LED series and parallel drive circuit characteristics

Date: Sep 19, 2019  | Click 23 times

image

LED series and parallel drive circuit characteristics 1. LED

What is the cause of the LED flashing?

Date: Sep 19, 2019  | Click 10 times

image

The use of LEDs is the choice of every household. However, s

Making 8×10 LED matrix with Arduino

Date: Sep 19, 2019  | Click 11 times

image

The LED matrix is some of the most popular projects built us

image

LED lighting has many advantages over traditional incandesce

Positive and negative judgment method of led lamp

Date: Sep 18, 2019  | Click 20 times

image

The principle of LED lights  LEDs are light-emitting diode

image

Is the led fluorescent lamp UV?  Fluorescent lamps are exc

How to wire the led sensor light

Date: Sep 18, 2019  | Click 21 times

image

 LED sensor light overview  LED sensor light is a new typ

image

Electronically controlled engine working principle  The bi

image

USB charger kit, also known as MP3/MP4 charger, input AC160-

12V High Efficiency White Light LED Driver

Date: Jun 28, 2019  | Click 22 times

image

12V High Efficiency White Light LED Driver







The memory is organized a paper detailed 51 MCU

Date: Mar 11, 2019  | Click 55 times

image

Program memory:The procedures used to store (binary image fi

Uled TV and Quantum Dot TV which is better

Date: Jan 06, 2019  | Click 44 times

image

Uled TV.ULED TV is to enhance the effect of television to op

Basic knowledge of inverter power supply design

Date: Nov 30, 2018  | Click 31 times

image

The power supply, as commonly understood, is a conversion de

copyright

© 2018-2019 www.loveelectronics.net Corp.All Rights Reserved.